[HELP] Probleme sur HARMAN KARDON AVR-460

[neostouve]

Bonjour les amis , j'ai un probleme avec mon avr-460 !

J'ai des coupures dans le décodage du son sur mon ampli (hdmi) , il se tape des délires tout seul !
J'ai deja changer de platine blu-ray et de cables hdmi , > pareil .


une idée ?

Comment faire la MAJ du firmware ???

MERCI
neo

[McBarrette]

Salut,

Pour faire la mise à jours il faut le relier au réseau internet par câble ethernet.

[neostouve]

Pfff j'ai du mal a comprendre pourquoi le son est dégradé sur le dolby digital ....

L'avr-460 ne possède pas encore la possibilité de se connecter au net via rj-45 .

J'ai trouver la procédure en pdf en téléchargeant le nouveau "bios". Il faut passer par l'usb en facade .

> verifier son bios >
Depending on when your AVR was manufactured, it may have already had the latest software installed at
the factory. To see if its software requires an upgrade, please follow these steps:
• With the AVR turned on, press the remote’s Setup button, and then press 1-2-3-0-OK on the remote.
• If the second line of the receiver’s front-panel display reads AFW v1.6.1.1, your receiver has this latest
software version and no further action is needed.
• If the display’s second line shows any other readout, please proceed with the upgrade

> flasher son bios >
1. If you have not already downloaded the upgrade file to your computer, do so now. Save the file in an
easy-to-find location.
2. Unzip the file you downloaded. It will contain four items: • an “Instructions.pdf” file, • a “Settings
Worksheets.pdf” file, • an “avr3601.bin” file, • a “torino.bin” file.
If you wish to have a printed copy of these instructions available to follow as you install the software,
save a copy of the “Upgrade Instructions.pdf” file to your computer for printout. If you want to write down
your system configurations, also save a copy of the “Settings Worksheets.pdf” file to your computer.
NOTE: Although one of the upgrade files is named “avr3601.bin”, it is correct for the AVR 3600,
AVR 2600, AVR 460 and AVR 360 model receivers.
3. Copy the “avr3601.bin” and “torino.bin” files to the root directory of a USB memory stick.
Before proceeding, make sure that your AVR is connected to a TV or video display so you can see its onscreen
menu (OSD). You will use the OSD to perform the following upgrade steps in your receiver.

4. Insert the USB memory stick into the receiver’s front-panel USB port. (If necessary, remove the frontpanel
connector cover to expose the port.)
5. Press the remote’s Setup button. The OSD will appear on the connected TV/video display.
6. Scroll-down to and select System. The System Settings screen will appear.
7. Scroll-down to System Info and select Upgrade Software. The System Upgrade screen will appear.
8. Select Continue, and then select Continue again. The receiver will search the USB stick for the new
.bin files.
9. Once the receiver detects the new files, select Continue again. The receiver’s front-panel display will
go blank and the volume control will slowly blink on and off. The front-panel display will show a progress
report as the upgrade is carried out.


10. When the receiver has completed the upgrade it will briefly go into the Standby mode.

11. The receiver will automatically turn on, and then will momentarily reset.
12. After a moment, the receiver’s front-panel display will read “Successful Continue”, and the OSD will
display “Software version 1.1, Continue.”

13. Press the OK button (select Continue). The OSD will shut off and the upgrade is now complete.
Before using your receiver, you should re-enter the input and speaker configuration settings and tuner
presets that you copied to your owner’s manual.

[McBarrette]

Et depuis la mise à jours il y a du changement ou pas du tout ?

[neostouve]

Et depuis la mise à jours il y a du changement ou pas du tout ?

non les décodages font n'importe quoi , il fonctionne que en stéréo ...

[McBarrette]

Il est bon pour le SAV

[neostouve]

Plus sous garantie , un SAV couterait plus chere qu'un ampli neuf 7.1 de bonne qualité ....